Turbidity & suspended solids instrumentation, historically based in Port Townsend, WA Product line now supported through Campbell Scientific, Inc.
A bold yellow angular logo mark set against a deep dark background, sharp and modern
D & A Instruments
Turbidity monitors & water-quality instrumentation

Optical suspended-solids monitoring during lake remediation dredging

Lake remediation dredging is often judged by the material removed, the improvement in water quality and the condition of the surrounding ecosystem. Yet the work also creates a difficult short-term problem: excavated sediment can form a plume that travels beyond the active dredge area. Optical suspended-solids monitoring provides a practical way to observe that plume continuously, relate sensor output to actual sediment concentration and support timely decisions while machinery is operating.

This case study describes a representative Australian lake remediation project using optical turbidity and suspended-solids instruments. The project team needed dependable measurements in shallow, variable water, with enough time resolution to distinguish dredging impacts from wind, stormwater inflows and ordinary resuspension. The example reflects the type of work undertaken in urban lakes, wetland basins and freshwater impoundments across Australia, where environmental approvals, community expectations and changing weather all influence the monitoring program.

Project setting and objectives

The lake was a shallow urban waterbody receiving runoff from developed catchments. Decades of sediment accumulation had reduced storage capacity, buried aquatic habitat and released nutrients under low-oxygen conditions. The remediation plan involved hydraulic dredging in defined cells, temporary transfer of sediment to a dewatering area and discharge of treated water back into the lake. A sensitive wetland outlet downstream created a firm requirement to control suspended sediment outside the work zone.

The project team established three monitoring objectives. First, it needed to measure background conditions before dredging began. Second, it had to identify increases in turbidity and suspended solids associated with each dredging cell. Third, it needed a defensible record showing whether controls worked and whether work practices should change. These objectives required more than occasional grab samples. A sample collected once or twice a day could miss a short plume generated by a change in cutter-head position, pump rate or barge movement.

The Australian setting added practical considerations. A sudden summer storm could wash fine material into the lake while the dredge was idle, and strong afternoon winds could resuspend soft sediment in the shallow margins. In Melbourne, Perth, Brisbane and other growing cities, urban lakes are often close to walking paths, roads and drainage infrastructure, so visible discolouration can quickly attract public attention. The monitoring plan therefore had to support environmental compliance and clear communication with the local community.

Building a defensible monitoring design

Before equipment was installed, the team mapped likely plume pathways using bathymetry, prevailing wind direction, inlet and outlet locations and the dredging sequence. A reference station was placed beyond the expected influence of the works, while impact stations were positioned near the dredge, at the downstream margin and close to the wetland outlet. The layout was reviewed after an initial dye-free trial because actual circulation was influenced by wind and the movement of the dredge pontoon.

Each station recorded optical turbidity, water temperature, depth and time. At selected points, the team collected water samples for laboratory total suspended solids analysis. Those samples were essential because optical response varies with particle size, mineral composition, colour and shape. A sensor calibrated in clear sand may produce a different result in water containing dark organic silt. The monitoring system therefore used local samples to convert instrument readings into a site-specific suspended-solids estimate.

The sensors were mounted so that they remained immersed during normal lake-level changes but could be removed for cleaning. Protective frames reduced the chance of impact from floating debris and small vessels. Cable routes were secured along the pontoon and marked around public access points, which was particularly important at a lake used by pedestrians, dog walkers and recreational fishers. The field team also recorded maintenance events, rainfall, dredging position and equipment settings in the same time series as the sensor data.

Turning optical response into solids data

Optical instruments estimate the concentration of suspended material by measuring how particles scatter or attenuate light. The output is commonly reported as turbidity, often in nephelometric units, but turbidity is not identical to mass concentration. A high reading indicates that light transmission has changed, yet it does not by itself state how many milligrams of sediment are present in a litre of water.

To create a useful relationship, the team collected samples across a broad range of conditions. Samples were taken during background periods, active cutting, pipeline changes, barge relocation and controlled plume events. In the laboratory, suspended solids were determined by filtration, drying and weighing. The laboratory results were then paired with the closest valid optical readings, with separate checks for unusually high values and periods affected by sensor fouling.

The calibration curve was initially close to linear over the working range, although the highest concentrations showed some flattening as the optical signal approached the instrument’s practical limit. The project manager therefore used the calibrated range for routine reporting and flagged readings outside it for confirmation by laboratory samples. This approach avoided presenting a false level of precision and made clear which results were measured directly, which were estimated and which required investigation.

Data quality depended heavily on maintenance. Fine sediment settled on the optical window after several hours near the dredge, while algae and biofilm developed during warm weather at the reference station. Wipers and scheduled cleaning reduced these effects, but automated checks were still required. Sudden step changes, prolonged identical readings and disagreement between paired sensors were treated as quality flags rather than genuine environmental events.

Managing dredging in real time

The monitoring dashboard displayed recent turbidity, estimated suspended-solids concentration, instrument status and rainfall. Rather than relying on a single universal trigger, the team used a tiered response based on the background range, the local calibration and the approval conditions for the project. A warning level prompted inspection and review of the dredge position. A higher action level required a reduction in pumping or cutting, investigation of containment and confirmation that the downstream station was not showing a sustained increase.

This system gave the dredging supervisor information quickly enough to change operations. When the cutter head entered a layer of soft, fine sediment, the near-field station recorded a sharp increase followed by a slower rise downstream. The supervisor reduced the advance rate and adjusted the pumping cycle. On another occasion, a moderate increase occurred at the outlet while the dredge was stationary. Rainfall records showed that the cause was likely catchment runoff rather than dredging, preventing an unnecessary shutdown while still prompting a visual inspection.

The team used separate readings for operational control and compliance reporting. Near-field sensors were valuable for detecting problems early, but the outlet station was more relevant to the receiving environment. This distinction reduced disputes about whether a short-lived high concentration beside the dredge represented a breach. It also helped the contractor understand that effective control meant limiting transport beyond the approved work area, rather than attempting to eliminate all disturbance at the excavation point.

For projects where plume movement interacts with currents or tidal exchange, measured data can be compared with numerical predictions. Guidance on turbidity data validation is useful when monitoring is being used to test a hydrodynamic model rather than simply trigger field responses. In a freshwater lake, the same principle applies: sensor observations can show whether predicted circulation matches what happens during changing wind and dredging conditions.

What the data revealed

The completed dataset showed that the largest suspended-solids pulses occurred during changes in dredging activity, not during steady operation. Starting the pump, moving the pontoon and clearing a partially blocked line disturbed sediment that had accumulated around the work area. Once the equipment settled into a consistent operating pattern, concentrations generally declined with distance. This finding led the contractor to introduce slower start-up procedures and a short stabilisation period before moving to the next dredging pass.

The data also separated three types of events that had initially appeared similar. Localised, short-duration spikes near the dredge were associated with excavation. Gradual increases at several stations during windy periods were linked to bed resuspension. Broad, lake-wide changes following rainfall were related to catchment inflows. Without continuous monitoring, these patterns would have been difficult to distinguish using occasional samples collected at fixed times.

The reference station became especially important during a week of unsettled weather. Turbidity increased there at the same time as readings at the impact stations, indicating that the lake-wide background had changed. The team retained the event in the project record but did not attribute the full increase to dredging. This prevented an exaggerated assessment of the work and supported a more credible report to regulators and the community.

At the end of the project, the monitoring record documented operating conditions, response actions, maintenance intervals and the relationship between optical measurements and laboratory solids results. The lake outlet remained below the relevant project trigger for sustained dredging-related impacts. The evidence also identified areas for future improvement, including better protection against fouling, earlier collection of calibration samples at extreme concentrations and more consistent recording of weather observations.

Practical recommendations for future projects

Successful optical monitoring depends on treating the sensor network as part of the dredging control system rather than as a separate compliance exercise. Equipment selection should reflect the waterbody, expected solids range, access conditions and maintenance capacity. A technically capable instrument can still produce weak evidence if it is poorly positioned, cleaned irregularly or disconnected from operational records.

For projects using D & A Instruments technology, product information and support arrangements should be checked through the current Campbell Scientific channel. The manufacturer’s former product range covers optical sensing applications in marine and freshwater environments, including suspended-solids measurement, turbidity monitoring and OEM integration. Relevant technical FAQs can help clarify installation, signal interpretation and application requirements before equipment is committed to the field.

Australian projects should also align the monitoring design with the applicable state or territory approval framework. Depending on the location, this may involve an environmental protection authority, a local council, a catchment management body or a waterway manager. The Australian and New Zealand Guidelines for Fresh and Marine Water Quality provide useful national context, but project-specific limits and reporting obligations come from the relevant approval and receiving environment. Clear chain-of-custody procedures for laboratory samples, accessible calibration records and prompt reporting of trigger exceedances strengthen the final evidence.

A well-designed optical suspended-solids program gives dredging teams a shared view of what is happening in the water. It supports fast operational decisions, helps distinguish construction impacts from natural variability and produces a transparent record for regulators and the public. For lake remediation in Australia, that combination is valuable: it protects downstream waters while allowing essential sediment removal to proceed with measurable control.