Turbidity & suspended solids instrumentation, historically based in Port Townsend, WA Product line now supported through Campbell Scientific, Inc.
A bold yellow angular logo mark set against a deep dark background, sharp and modern
D & A Instruments
Turbidity monitors & water-quality instrumentation

Optimizing Coagulant Dosing with Suspended-Solids Sensors

At a drinking water plant, coagulation is often managed through jar tests, operator experience, flow measurements, and periodic laboratory analysis. These methods remain valuable, but they can miss rapid changes in raw-water quality. A storm, reservoir turnover, upstream construction project, or seasonal runoff event may alter suspended-solids loading faster than a manual sampling program can capture it.

This case study describes a practical monitoring strategy in which online suspended-solids sensors supported more responsive coagulant control. The example is based on a representative surface-water treatment plant with variable influent quality, rather than a claim about one named facility. It shows how optical measurement, process knowledge, and controlled dosing logic can work together without removing operators from the decision-making process.

The objective was not simply to increase or reduce chemical use. The plant wanted to maintain consistent floc formation and settled-water clarity while avoiding excess coagulant, unstable filter performance, and unnecessary sludge production. Suspended-solids data provided an additional process signal between intermittent laboratory tests and the final treated-water measurements.

Why Raw-Water Variability Disrupted Chemical Control

The plant treated reservoir water whose solids concentration changed throughout the year. During stable weather, the raw-water stream had relatively predictable characteristics. Rainfall introduced fine mineral particles and organic material, while seasonal mixing redistributed settled material within the reservoir. These changes affected the amount of coagulant needed to destabilize particles and form settleable flocs.

Operators initially adjusted the chemical feed using a combination of raw-water turbidity, flow rate, historical settings, and jar-test results. Turbidity was useful, but it did not always represent mass loading consistently. Two water samples could have similar optical cloudiness while containing different particle sizes, shapes, or concentrations. The relationship between turbidity and suspended solids also shifted when the source-water composition changed.

This created two operational risks. An underfeed could leave fine particles in the clarified water, increasing the burden on filters. An overfeed could raise chemical costs, increase sludge volume, and create residual-control problems. The plant needed a measurement that could track suspended material continuously and provide an early indication of changing coagulation demand.

Building A Measurement-Based Dosing Strategy

The monitoring arrangement used an optical suspended-solids sensor installed in the raw-water channel upstream of rapid mixing. The sensor measured the light-scattering response of particles in the water. Because optical readings depend on particle characteristics, the plant developed a site-specific correlation between sensor output and laboratory suspended-solids results rather than applying a generic conversion.

Calibration samples were collected across a broad operating range. The team included clear-water conditions, normal daily flow, post-rainfall events, and high-solids periods. Each sample was analyzed in the laboratory, and the results were compared with the sensor signal. This produced a working calibration curve and revealed when the relationship became less reliable at the upper end of the range.

The plant also reviewed the sensor’s installation environment. Bubbles, vibration, excessive flow turbulence, biological growth, and deposits on optical windows can affect measurements. A stable mounting point and a cleaning routine were therefore treated as part of the measurement system, not as optional maintenance tasks. The broader value of optical instruments is illustrated by their use across changing freshwater and marine environments, including applications described in multi-parameter profiling.

From Sensor Signal To Coagulant Setpoint

The initial control logic was deliberately conservative. The suspended-solids measurement did not directly command a large chemical change. Instead, it adjusted a feed-forward dosing recommendation that operators reviewed alongside flow, pH, alkalinity, temperature, and treated-water performance.

A simplified dosing calculation used the following structure:

[ \text{Coagulant feed} = \text{water flow} \times \text{dose response to solids} \times \text{operating correction} ]

The dose response was developed from jar tests and historical operating data. The operating correction accounted for pH, alkalinity, temperature, and any known source-water condition that affected floc formation. A feedback component then used settled-water turbidity and filter influent trends to prevent the system from relying on the suspended-solids sensor alone.

This layered approach was important because suspended-solids concentration does not fully define coagulation demand. Particle surface chemistry, natural organic matter, water temperature, and alkalinity can all change the required dose. The sensor served as an early-warning and feed-forward instrument, while downstream water-quality measurements confirmed whether the treatment response was acceptable.

During commissioning, the plant imposed rate limits on automatic changes. For example, the dosing system could respond more quickly to a sustained increase in solids than to a brief isolated spike. A moving average reduced sensitivity to bubbles or transient disturbances, and an alarm notified operators when the sensor value moved outside its validated range.

Operating condition Sensor response Dosing response Operator check
Stable, low-solids water Consistent baseline Maintain or trim dose within approved limits Review settled-water turbidity
Gradual rainfall-related increase Sustained upward trend Increase feed-forward dose in small steps Confirm pH and alkalinity
Short optical spike Abrupt, isolated change Hold automatic adjustment Inspect sensor and sample water
High-solids event Extended elevated reading Apply event setpoint or controlled ramp Run jar test and verify mixing
Sensor fouling or signal fault Implausible or unstable output Revert to validated backup setting Clean, inspect, and recalibrate

Field Deployment And Data Validation

The plant began with a monitoring-only period. For several weeks, the sensor recorded raw-water conditions while operators continued to use the existing dosing method. This baseline made it possible to compare solids trends with coagulant use, settled-water turbidity, filter run time, sludge blanket behavior, and laboratory results.

During this period, operators identified a recurring pattern: the raw-water solids signal often began rising before the effect appeared in settled-water turbidity. That lead time gave the treatment team an opportunity to prepare for changing conditions instead of responding after clarification performance had already deteriorated. The relationship was especially useful during rainfall events, when source-water quality shifted over several hours.

The equipment was selected and managed with the practical requirements of field instrumentation in mind. D & A Instruments has experience with optical sensing technologies for suspended solids, turbidity, hydrology, environmental research, and OEM integration; its product information and support pathways are available through the instrumentation resource. For this plant, the most important considerations were cleanability, access for calibration checks, signal stability, and compatibility with the control system.

Validation continued after the sensor was connected to the dosing recommendation. Operators collected paired samples whenever the process changed rapidly or the signal approached an alarm threshold. If laboratory results disagreed with the online reading, the team investigated sampling location, particle composition, sensor fouling, and hydraulic conditions before changing the calibration.

Operational Results And Process Safeguards

After the trial period, the plant observed more stable coagulant use during changing raw-water conditions. The greatest benefit appeared during moderate solids increases, where the feed-forward signal helped the process move toward an appropriate dose before settled-water quality began to drift. The plant did not eliminate jar testing; instead, jar tests became more targeted and were used to confirm the dose response during unusual events.

Chemical consumption also became easier to interpret. Previously, a higher daily dose could reflect either increased solids loading or operator caution. With continuous solids data, the plant could compare chemical use with the incoming particle burden and identify periods when the dose was rising without a corresponding change in water quality. This improved process review and supported more disciplined adjustments.

The sensors did not produce a perfect solids measurement under every condition. High air entrainment, coating, very coarse particles, and changes in particle color or composition could affect the optical response. For that reason, maintenance and long-term performance testing were included in the operating procedure. Guidance on optical stability testing is relevant when a utility needs to distinguish true water-quality changes from instrument drift.

Safeguards included manual override, high and low signal alarms, a fallback dose schedule, and a requirement for operator review after sensor cleaning or calibration. The control system also prevented rapid oscillation by applying minimum hold times and gradual setpoint changes. These measures reduced the likelihood that a single bad reading would cause an inappropriate chemical response.

Lessons For Treatment Plant Implementation

The case demonstrates that suspended-solids monitoring is most effective when it is integrated into a broader treatment model. A sensor can reveal how much particulate material is entering the plant, but it cannot independently determine the correct coagulant dose under every chemical and hydraulic condition. The process response still depends on mixing energy, pH, alkalinity, temperature, particle properties, and the selected coagulant.

The calibration program was therefore as important as the hardware. Laboratory samples established the local relationship between optical signal and solids concentration. Repeated checks across seasons helped the team recognize when that relationship shifted. A calibration that works for mineral-rich runoff may not perform identically when the source contains more algae, organic matter, or fine clay.

Data quality also depended on installation details. The sensor location had to represent the incoming water without excessive bubbles or dead zones. The plant documented cleaning intervals, inspection findings, laboratory comparisons, alarm responses, and control changes. Over time, this created an operational record that supported both troubleshooting and chemical optimization.

The approach can be scaled according to plant size and automation maturity. A small facility may use the sensor as an alarm and dosing aid, while a larger plant may connect it to a supervisory control system with feed-forward and feedback logic. In either case, operators should be able to see the raw signal, filtered value, alarm state, calibration status, and current dosing response.

Practical Steps For A Reliable Deployment

A utility considering this approach can reduce risk by treating the project as a process-control improvement rather than a simple sensor installation.

A staged commissioning plan gives the treatment team time to learn how the measurement behaves in real plant conditions. It also helps separate a genuine change in source-water solids from a fouled optical window, entrained air, or an unsuitable mounting location.

For plants with variable surface-water quality, continuous suspended-solids information can make chemical control more timely and more defensible. The technology is most valuable when its readings are interpreted alongside water chemistry and downstream treatment results, creating a coordinated view of the entire clarification process.

D & A Instruments’ technical resources provide background on optical sensing, suspended-solids measurement, turbidity monitoring, hydrology, and related water-quality applications. Treatment professionals can review the available instrumentation information and contact the current product support organization through the resources provided by Campbell Scientific to evaluate a suitable monitoring configuration for their plant.