Turbidity & suspended solids instrumentation, historically based in Port Townsend, WA Product line now supported through Campbell Scientific, Inc.
A bold yellow angular logo mark set against a deep dark background, sharp and modern
D & A Instruments
Turbidity monitors & water-quality instrumentation

Deploying Suspended-Solids Sensors in Vertical Flow Constructed Wetlands

Vertical flow constructed wetlands are increasingly used to polish wastewater, stormwater and industrial effluent where a low-energy treatment process is valuable. Their planted beds, graded filter media and intermittent dosing can remove fine particles, nutrients and organic matter, yet performance depends heavily on how solids move through the system. A suspended-solids sensor can reveal changes that grab samples may miss, particularly during high-flow events or after maintenance.

Monitoring is more complicated than placing a probe in an open pond. Water moves down through layers of sand, gravel and organic material, while air enters the bed between doses. The most useful measurement points are usually accessible inlet and outlet streams, sampling chambers or bypass lines rather than the media itself. Correct placement, calibration and cleaning determine whether the resulting data supports sound operational decisions.

Why Solids Behaviour Matters In Vertical Beds

A vertical flow wetland commonly receives wastewater in batches through a distribution network across the bed surface. The dose passes through the filter media, and the bed drains before the next application. This alternating wetting and aeration supports biological treatment, but it also creates changing hydraulic conditions. A short, intense dose can carry a concentrated solids pulse to the inlet, while the outlet may respond later as water travels through the media.

Suspended solids include mineral particles, organic flocs, algae and biological fragments. Total suspended solids (TSS) is normally reported as a mass concentration in milligrams per litre, whereas turbidity describes the way particles scatter or absorb light. The two measurements often correlate, but they are not interchangeable. A wetland treating greywater, food-processing wastewater or stormwater may receive particles with very different size, colour and density characteristics.

Continuous or event-based optical monitoring helps identify solids breakthrough, filter clogging and changes in influent quality. A rising inlet signal may indicate a catchment disturbance or failed upstream screening. A gradual increase in outlet concentration can point to media disturbance, preferential flow, hydraulic overload or a dosing problem. Comparing inlet and outlet trends gives a more useful picture than relying on a single laboratory result collected once each day.

The operating context is important in Australia. A wetland near Brisbane may receive intense summer rainfall that rapidly changes stormwater solids loads, while a site outside Perth may experience long dry periods followed by highly concentrated first-flush runoff. In regional New South Wales, small communities may need remote monitoring because operators cannot visit a treatment site after every rainfall event. A sensor can provide early evidence that a bed needs inspection before an exceedance becomes persistent.

Choosing Measurement Points And Flow Paths

The inlet location should represent the water actually entering the wetland, not a quiet corner where heavy particles settle. A probe installed in a well-mixed feed channel, dosing main or sampling chamber can capture the concentration delivered to the bed. If a pump supplies several cells, the measurement point should account for batch operation and confirm whether each cell receives comparable loading.

The outlet point must be selected with equal care. Effluent from a vertical bed may contain air bubbles immediately after dosing, and a shallow drain can have intermittent flow. A sensor mounted directly in a turbulent drop or open discharge may report bubbles and surface interference as apparent solids. A calm, continuously wetted chamber or a representative bypass loop generally provides a more stable optical path.

Sensors placed inside the filter media create a different measurement problem. Porewater can be sampled through dedicated wells, but the probe must tolerate restricted access, fouling and changing water levels. Media particles can abrade the instrument, and an optical window may become coated with biofilm or iron deposits. For most operational projects, accessible inlet and outlet monitoring is more reliable than trying to measure suspended particles within the bed.

Hydraulics should be documented before installation. Record the dosing cycle, expected flow range, pipe diameter, residence time, normal water level and likely low-flow condition. In a constructed wetland serving a remote Northern Territory facility, evaporation and seasonal rainfall may produce larger changes in flow than the treatment design suggests. In an urban Melbourne installation, stormwater inflow and pump cycling may produce rapid transitions that require a fast response sensor and time-synchronised flow data.

Matching Optical Technology To The Water

Optical suspended-solids instruments estimate concentration by measuring light scattered or attenuated by particles. Near-infrared wavelengths are common because they reduce interference from visible ambient light and provide useful sensitivity across many wastewater applications. The measured signal depends on particle size, shape, colour, concentration and the geometry of the optical system, so an instrument calibrated in one water source should not automatically be treated as accurate in another.

Selection begins with the expected solids range rather than the average value. A clean treated effluent may require high sensitivity at low concentrations, while an influent line receiving stormwater may need a wider range and resistance to signal saturation. The sensor should also suit the installation environment: immersion depth, pressure, cable length, temperature, communication protocol and available power all matter. Australian projects may use solar power and telemetry at isolated sites, making low energy demand and reliable data logging especially valuable.

Technical resources from D & A Instruments explain optical sensing approaches used for turbidity and suspended-solids applications across freshwater and marine environments. Those principles transfer well to wetland monitoring, provided the instrument is calibrated against the actual water and particle population found at the site. A turbidity monitor may be suitable for trend detection, while a solids sensor configured for local TSS reporting may be preferable where discharge limits are expressed as mass concentration.

The installation should prevent direct sunlight, excessive vibration and unnecessary turbulence. A flow-through cell or bypass arrangement can protect the sensor from floating debris and make cleaning safer, although the bypass must maintain representative flow. In an open channel, mounting hardware should keep the optical window away from the bed, walls and any zone where settled material accumulates. A wiper can extend deployment time, but it does not replace inspection when the water contains grease, fibres or sticky biological matter.

Calibrating And Validating Field Measurements

Site-specific calibration is essential because optical response varies with particle characteristics. Collect water samples across the expected operating range, including clear conditions, normal loading and high-solids events. Each sample should be mixed carefully, preserved and analysed using an appropriate gravimetric TSS method. Pair the laboratory result with the sensor reading at the same time and under stable flow conditions.

A calibration curve may be linear over part of the range and non-linear at higher concentrations. Do not force a single equation across values where the optical detector begins to saturate. Multiple-point regression, separate wet-weather and dry-weather relationships, or a turbidity-to-TSS conversion may be appropriate, depending on the project objective. The calibration record should include sampling location, time, flow, weather, sensor settings and laboratory method.

Particle size can change after rainfall, construction activity or a process alteration upstream. Fine clay may produce a strong optical signal at a relatively low mass, while dense sand can produce a greater mass concentration with a different response. Guidance on sensor selection in high-sediment rivers is relevant here because it highlights the importance of particle characteristics and range when choosing an optical measurement system.

Validation should continue after commissioning. Compare logged readings with periodic laboratory samples and inspect whether the relationship changes after a season, media replacement or major catchment event. A sensor that tracks trends consistently can be valuable even when exact TSS conversion is uncertain, but the limitations must be documented. For regulated discharge reporting, laboratory confirmation and an approved sampling method may still be required by the relevant state or territory authority.

Managing Fouling, Air And Data Quality

The main practical threats are fouling, bubbles, sediment deposition and intermittent flow. Biofilm on an optical window usually causes a slow drift, while trapped air can create sharp spikes or erratic values. Heavy particles settling around the probe may produce a falsely low or unstable reading if the water at the optical path is no longer representative. A diagnostic system should record signal quality, sensor status and, where available, fouling or obstruction indicators alongside the concentration.

Routine maintenance should follow the loading of the site rather than an arbitrary calendar alone. Inspect the probe after the first few weeks, then adjust the interval based on observed fouling. Clean the optical surfaces with materials approved by the manufacturer, check cable glands and mounting hardware, and confirm that the sensor remains aligned. Field staff should collect a verification sample before cleaning when a suspicious trend needs investigation.

A useful monitoring setup combines solids concentration with flow, water level, dosing status and rainfall. A concentration spike during a high-flow event has a different meaning from the same spike during a normal dose. If the outlet signal rises without an inlet change, operators can investigate media disturbance, short-circuiting or a drain problem. If both signals rise together, the cause may be upstream loading rather than wetland failure.

Experience from other water systems also supports disciplined sensor care. The discussion of cooling-water fouling prevention demonstrates why early detection of particle loading and regular optical maintenance matter in harsh environments. Constructed wetlands have different hydraulics, but the same fundamentals apply: keep the optical path clean, interpret readings with flow information and treat sudden changes as signals requiring context.

Turning Measurements Into Wetland Decisions

The value of monitoring lies in linking a solids signal to an operational response. An elevated inlet concentration may trigger inspection of screens, septic tank desludging, upstream erosion controls or industrial pretreatment. Persistent outlet solids may justify checking distribution pipes, removing accumulated surface material or reviewing the dosing schedule. Data can also show when a bed is recovering after maintenance rather than relying on visual appearance alone.

For Australian water managers, records should align with the site’s approval conditions and sampling obligations. Requirements differ between jurisdictions, and a system regulated by the NSW Environment Protection Authority is not necessarily documented in the same way as one overseen by the Queensland or Victorian regulator. Data timestamps should use a clear time standard, especially when comparing rainfall, pump events and laboratory samples. Remote telemetry is particularly useful for sites supporting recycled-water schemes near Adelaide, Canberra or growing peri-urban communities.

A practical monitoring programme normally includes commissioning checks, a documented calibration, scheduled verification samples, maintenance logs and alarm limits based on local operating history. Alarm thresholds should allow for normal batch dosing and should not be copied from another wetland without adjustment. Trend alarms, rate-of-change alarms and missing-data alerts can be more informative than a single fixed concentration limit.

When properly installed, a suspended-solids sensor becomes part of the wetland’s process control rather than an isolated measuring device. It can show how particle loading changes with weather, hydraulic operation and catchment activity, while supporting better maintenance decisions and defensible performance records. In vertical flow systems, the combination of representative sampling points, site-specific calibration and careful interpretation is what turns optical readings into reliable treatment intelligence.