Turbidity & suspended solids instrumentation, historically based in Port Townsend, WA Product line now supported through Campbell Scientific, Inc.
A bold yellow angular logo mark set against a deep dark background, sharp and modern
D & A Instruments
Turbidity monitors & water-quality instrumentation

How to Zero a Field Turbidity Sensor Without Disturbing the Sample

Long-term turbidity datasets from Australian rivers, ports, and coastal waters only stay credible if the sensor's baseline is regularly verified. Optical probes mounted on pontoons in Sydney Harbour, on frames in the Brisbane River, or buried in tailings ponds in the Pilbara cannot easily be lifted out for a bench zero check. Pulling the sensor disturbs the very water volume being measured, lets in light, changes the flow regime around the optic, and almost always breaks the time record. Field staff need a way to verify the zero reading in place, using water drawn from the same matrix as the sample.

The method described here keeps the sensor wet, in position, and surrounded by essentially the same hydrochemistry, but exposes its optic to a particle-free reference for a short window. It works on backscatter, 90-degree scatter, and infrared absorption probes alike, including the suspended-solids and turbidity instruments formerly supplied by D & A Instruments and now backed by Campbell Scientific. Australian conditions make the approach particularly valuable: high UV, episodic algal blooms in the Murray–Darling system, tidal resuspension in Port Phillip Bay, and tropical biological fouling on the Great Barrier Reef coast can all push a baseline off within weeks of deployment.

What a turbidity zero actually represents

An optical turbidity sensor reports a signal derived from light scattered or attenuated by particles suspended in the measurement volume. The zero point is the reading produced when that volume contains no particles, only the water itself. In a clean, particle-free matrix, any residual signal is due to electronic offsets, window reflections, bubble scattering, temperature effects on the photodiode, and stray light reaching the detector. As soon as fine sediment, plankton, microbubbles, or organic floc enters the volume, the signal rises.

Field zero drift happens slowly. Window fouling adds a small constant offset that creeps upward over days. Temperature swings change detector dark current, especially on instruments that do not fully compensate. Optical surfaces can develop micro-condensation films in humid Queensland air or salt crusts on a tidal deployment. Air bubbles clinging to the optic window scatter strongly and look like particles, even in clean water. A useful zero check separates these sources so that drift can be quantified and corrected without trusting the in-situ readings blindly.

The reason for doing the check in place, without disturbing the sample, is to preserve the optical geometry, the temperature of the water touching the window, and the chemistry of the matrix. Lifting the sensor into a bucket of clean tap water changes all three. The bucket water is colder, has different ionic strength, often carries dissolved gases that have come out of solution, and may not match the refractive index of the deployment water. An offset measured against tap water is not the same offset as one measured against site water.

Preparing the site and the operator

Before any zero work, confirm the deployment is legal and safe. State water authorities require permits for hands-on work in many New South Wales and Queensland waterways, and port corporations in Brisbane, Newcastle, and Fremantle impose their own access rules. For environmental data intended to be compared against ANZECC trigger values or local EPA objectives, the field log must record the time of any maintenance, the operator, and the conditions on the day, otherwise the data point may have to be flagged or rejected.

Work out the tide and weather window first. On a coastal or estuarine deployment, the zero check is best done at slack water when suspended load is lowest and the flow around the sensor is most stable. In a stormwater pond or a settling lagoon, aim for a calm morning with no recent inflow. Choose a time when the operator can stand or kneel without rocking the frame, because any motion relative to the sensor changes the particle population near the optic and defeats the purpose of the check. Sun shade over the optic helps in bright tropical light, particularly during work on the Great Barrier Reef coast where midday glare can swamp a detector during the manual phase.

Have a clean container, a small peristaltic pump or large syringe, a 0.2 µm capsule filter, and a dark shroud ready on the boat or pontoon. A handful of clean lint-free wipes, a wash bottle with deployment water, and a notebook for recording readings are also worth carrying. Where the deployment is in drinking-water catchment or near a recreational beach, follow the local council's water-safety guidance and wear a PFD; routine zero checks have a way of happening on the windiest day of the year.

Building a particle-free reference at the sensor

A clean reference does not need to be a calibrated standard. It only needs to be particle-free water with the same temperature and roughly the same refractive index as the water around the sensor. The simplest source is site water drawn through an in-line 0.2 µm capsule filter into a darkened container, with care taken to avoid introducing air. Bubbles are the most common reason a "zero" looks noisy in the field.

Bring the filtered water to the sensor in a way that does not disturb the sample. Two field methods work well. The first uses a sealed flow-through cell or a soft plastic shroud that presses against the optic window, with filtered water fed in slowly from a syringe or peristaltic pump. The second uses a darkened bottle or cuvette held directly against the optic, with a small vent so air can escape as water fills the volume. In stirred reactors and process tanks the shroud design is slightly different because the optic sits in a flowing matrix rather than still water, and the process control placement notes describe the small changes in equilibration time that apply in those rigs. In both natural-water and process cases the optic stays submerged, the geometry is unchanged, and the surrounding water is not agitated. Air must be excluded; even a single bubble on the window can bias the reading upward by tens of NTU.

For seawater work, filtration should be done with a membrane that has been pre-rinsed with site water so the filtrate carries the same salt content and refractive index. For freshwater work in places like the Murray River or a Pilbara mine pit lake, the same approach works, but pre-rinsing with site water is even more important because freshwaters vary in dissolved organic content. Where on-site filtration is impractical, a small volume of distilled water brought from the lab can be used, provided a separate blank has already been measured to confirm that the container itself is not shedding particles.

Running the zero check with the sensor in place

Once the reference is in contact with the optic, watch the reading for at least a minute. Optical detectors often settle slowly as the reference water reaches the same temperature as the optic window, especially after a sunny day on a black-powder-coated housing in Queensland. Record the minimum value reached, the value after sixty seconds, and the value after two minutes. A drift of more than a few hundredths of a NTU over two minutes usually points to a small bubble moving across the window or to thermal equilibration still in progress.

Compare the field zero against the factory zero stored in the instrument and against any zero measured on a previous site visit. A small offset is normal and can be entered as a correction in the data logger or processing software. A large or sudden offset, particularly after a flood event, a biofouling bloom, or mechanical work on the frame, should trigger a closer look at the optic and at the wiper or anti-fouling head if fitted. ANZECC-style reporting protocols generally require that offsets larger than the method detection limit be flagged in the dataset and not silently removed.

When the reading has stabilised, remove the reference slowly so that site water flows back across the window without trapping air. Confirm that the live reading returns to its pre-check value within a few per cent. If it does not, the check itself may have introduced a small bubble or a thermal step, and it is worth repeating once the sensor has settled. Always finish with the sensor wet, in position, and logging, not dry on a bench.

Logging the result and acting on the data

Every zero check produces a small dataset: the time, the operator, the temperature, the weather, the reference water source, the minimum and final zero readings, the factory zero used for comparison, and any corrective action taken. Store these notes with the turbidity record. Australian projects reporting against the National Water Quality Guidelines or state EPA objectives are routinely audited, and a missing maintenance log is one of the most common reasons a long dataset gets partially invalidated.

For dredging and port work, the consequences of an unnoticed baseline shift are particularly large because the receiving environment may be a sensitive estuary or a marine park. Practical guidance on baseline handling in spoils areas is available in the dredge spoil disposal guidance published by the manufacturer. If the offset is small and stable, apply it as a flat correction and note the date in the metadata. If the offset is drifting between visits, schedule a clean and re-zero rather than chasing a moving target with software. Worn wiper blades, etched windows, and detector ageing are easier to fix when caught early.

Keeping the zero stable between visits

A single careful zero check is only useful if the next one tells a similar story. Routine visits every four to eight weeks are typical for Australian freshwater deployments, with shorter intervals in warm tropical waters and longer intervals in cold, low-productivity southern waters such as those around Hobart or Macquarie Harbour. Between visits, keep biofouling in check with the wiper or air-burst system fitted to the instrument, and avoid running the sensor dry or in air for long periods, which can leave dried films on the optic that rehydrate unevenly.

When an offset refuses to stabilise between visits despite clean optics and a working wiper, the issue is often detector ageing rather than fouling, and the next step is to compare the field zero against a freshly prepared reference on the bench. Where this is not practical in remote locations, send the readings and the field log through the technical support resources maintained by Campbell Scientific, who took over product management for the former D & A Instruments line. The time invested in a clean, repeatable in-situ zero check pays back many times across a long deployment. The reading becomes easier to defend at audit, the data series stays continuous, and the operator leaves the site knowing exactly what the instrument was reporting when the next sample arrives from the lab.