Turbidity & suspended solids instrumentation, historically based in Port Townsend, WA Product line now supported through Campbell Scientific, Inc.
A bold yellow angular logo mark set against a deep dark background, sharp and modern
D & A Instruments
Turbidity monitors & water-quality instrumentation

Fixing Erratic Turbidity Readings Caused by Air Bubbles in Sensors

Air bubbles are the quiet saboteurs of optical turbidity monitoring. Whether a probe sits on a pontoon in Sydney Harbour, hangs from a frame in a Tasmanian salmon pen, or rides the turbulence of a Brisbane River dredge plume, an unseen pocket of gas can scatter light exactly the way a suspended particle does. The result is a sensor trace that spikes without warning, drifts between calibrations, and refuses to settle no matter how carefully the optics are wiped.

For Australian operators working under the Australian and New Zealand Guidelines for Fresh and Marine Water Quality, those spikes are not just inconvenient. They compromise compliance reporting, skew dredge-window decisions, and erode confidence in long-term datasets that took months of fieldwork to collect. Understanding how bubbles enter the measurement path, and how to remove or mask their influence, is therefore an everyday skill for anyone deploying in-situ turbidity instruments across Australia's estuaries, mine pits, and aquaculture leases.

Why air bubbles confuse optical turbidity probes

Optical turbidity sensors work by projecting a beam of light into the water column and measuring what comes back. Nephelometric designs detect scatter at right angles to the source, backscatter units read light reflected nearly in line with the beam, and combined sensors use both. Each technique assumes that whatever disrupts the beam is a particle of sediment, organic matter, or algae.

Air bubbles are the awkward exception. A bubble as small as 50 micrometres bends and scatters light in a pattern that looks remarkably similar to a fine silt grain. When bubbles pass through the sensing volume in a stream of moving water, the sensor records a rapid fluctuation rather than a steady value. Multiply that effect across a choppy afternoon on Port Phillip Bay and the data file will look like static.

The problem is amplified in shallow Australian deployments where surface agitation is constant. A probe mounted half a metre below the waterline on a wave-washed jetty in Coffs Harbour will see far more bubbles during a southerly buster than during a calm dawn tide. Without context, the recorded values appear nonsensical, yet the instrument itself is functioning perfectly well.

Where bubbles actually come from in the field

Bubbles rarely arrive from nowhere. In most Australian installations they enter the water through pumped systems, biological activity, mechanical cavitation, or degraded seals.

Pumped systems are the usual suspects. Any submersible setup that pulls water past the sensor through tubing can entrain air at the intake if the line is not fully submerged, or at a fitting that has loosened in service. In the tidal reaches of the Derwent estuary near Hobart, where water levels swing by more than a metre between neap and spring tides, a pump inlet that was well below the surface at high water can sit just beneath the meniscus at low water.

Biological activity generates its own gas. Warm, sunlit waters off the Queensland coast are famously productive, and prolific photosynthesis in seagrass meadows around Cairns can push dissolved oxygen above saturation, releasing fine bubbles from leaves and blades. Those bubbles drift past the probe and register as false turbidity. Mechanical cavitation is harder to spot: a centrifugal pump running at the wrong speed, or a diaphragm pump with a tired valve, can vaporise small pockets of gas right at the sensor face, with a signature of high-frequency noise rather than broad spikes.

The fourth source is simply atmospheric air drawn in through a degraded seal or cable gland. After a season of UV exposure and salt spray, even a well-made sensor head can develop a tiny leak. Perth operators who service their instruments at the end of each summer often catch this before it becomes a data problem.

Field diagnostics that separate bubbles from real signal

Before changing hardware, a careful diagnostic pays off. A bubble problem usually shows identifiable patterns that distinguish it from genuine turbidity events.

Time of day is a useful first filter. If the noise spikes cluster during windy afternoons and disappear at dawn, suspect surface agitation rather than the sensor. A plot of the data alongside wind speed from a nearby Bureau of Meteorology station often makes the connection obvious. In contrast, a real plume event from a maintenance dredge in Botany Bay will produce a coherent mass of elevated readings that rises and falls over hours, not minutes.

A simple in-situ test helps too. Lift the sensor out of the water, hold it briefly so any clinging bubbles can run off, and re-submerge it gently. If the noise immediately drops and then climbs again as the water moves, bubbles were the issue. If it remains erratic, the optics or the cable may need attention.

Comparing two sensors side by side is the most reliable field check. If one probe reports wildly varying values while an identical unit nearby reads steady, the suspect instrument probably has a bubble issue specific to its mounting or plumbing. Many Australian environmental consultancies now deploy paired sensors for exactly this reason, particularly on long-term estuarine monitoring contracts.

Hardware adjustments that reduce bubble exposure

Once bubbles are confirmed as the culprit, the cure usually lives in how the sensor is installed rather than in the sensor itself. Mounting depth is the first lever to pull.

Dropping the probe a further thirty or forty centimetres below the surface takes it out of the bubble-rich surface layer that wave action creates. In choppy coastal sites such as Fremantle's fishing boat harbour or the open sections of Port Phillip Bay, this small adjustment often removes most of the noise without any change to the optics.

A flow-through cell with a downward-facing inlet lets bubbles rise out of the water before it reaches the sensing window. This arrangement is common on pumped systems serving water-treatment plants in regional centres like Wagga Wagga or Ballarat, where operators need stable readings for regulatory discharge monitoring. The same approach works well across many supported applications, from aquaculture to harbour-side dredging campaigns.

Cable management matters more than many operators realise. A sensor cable that hangs slack and swings in the current can act like a pump, drawing bubbles across the optics with each movement. Tethering the cable firmly above and below the probe reduces this self-induced agitation.

Software strategies for cleaner datasets

Hardware adjustments will not eliminate every bubble event, particularly during storms. A thoughtful logging and filtering strategy bridges the gap.

A rate-of-change filter rejects values that change faster than the physical system can plausibly produce. Real sediment plumes move through the water column at speeds set by currents and settling rates, and they do not produce millisecond-scale jumps. A simple threshold applied to the second derivative of the signal removes the worst spikes without touching genuine events.

Suspect-data flags help when communicating with stakeholders. Rather than silently deleting noisy readings, marking them as low-confidence allows the downstream analyst to decide whether to use them. Australian mine-site operators have found this approach useful when submitting data to state regulators under mine-lease water-management plans, where every data point may later be scrutinised.

Complementary measurements also strengthen confidence. Pairing the turbidity sensor with a pressure transducer and a small optical dissolved-oxygen probe helps separate true plume events from bubble artefacts, since bubbles and oxygen saturation often rise together while genuine sediment plumes do not. The same logic is described in detail in a dredging time case study that combines turbidity, current, and depth data to time maintenance work in busy ports. Choosing the right installation architecture, whether pumped, submersible, or flow-through, comes down to site-specific factors such as depth, current, and access for cleaning.

Long-term prevention and maintenance routines

Bubble-induced noise is rarely a one-off event. It tends to creep back in as seals age, biofouling builds up, and pumping systems drift out of tune. A short, written schedule keeps the problem from returning.

Quarterly inspections should include a visual check of the optical face, the condition of seals and cable glands, and a quick test of any pump or wiper mechanism. In warm-tropical waters around Darwin, biofouling can colonise a probe face within weeks, and the resulting sloughing material often traps small bubbles against the optics. Routine cleaning with a soft brush and clean water, taking care not to scratch the window, prevents the worst of this. On platforms such as unmanned surface vessels, motion and vibration make bubble control even more critical, and the notes on unmanned surface vessel deployments cover that in more detail.

Annual calibration in still, bubble-free conditions restores the baseline. A bucket of deionised water or filtered tap water, allowed to stand for several hours, provides a stable reference. Field calibration against a portable reference instrument can then be applied for site-specific corrections, but the laboratory-style zero and span check should never be skipped.

Records matter, and so does the supply chain behind the instrument. A simple log of cleaning dates, replaced parts, and observed bubble behaviour builds an institutional memory that helps the next operator diagnose problems faster. Australian environmental consultancies working on multi-year monitoring contracts for state agencies have found that keeping such logs pays for itself many times over when questions arise during an audit. Choosing a sensor platform backed by an Australian distributor familiar with local conditions, from tropical harbours to alpine reservoirs, helps ensure that spare wipers, calibration kits, and replacement seals are within reach when the next field trip begins.

Practical steps to eliminate bubble-induced noise