Turbidity & suspended solids instrumentation, historically based in Port Townsend, WA Product line now supported through Campbell Scientific, Inc.
A bold yellow angular logo mark set against a deep dark background, sharp and modern
D & A Instruments
Turbidity monitors & water-quality instrumentation

Using groundwater profilers to assess aquifer storage and recovery performance

Aquifer storage and recovery (ASR) captures water during periods of availability, injects it into a suitable aquifer, and recovers it when demand increases. The method can reduce pressure on surface reservoirs and provide a valuable buffer through Australia’s dry seasons. Its performance depends on what happens below ground after injection, where water quality, density, pressure and sediment movement can vary sharply over short vertical distances.

Groundwater profilers provide a practical way to observe these changes. Instead of relying only on samples from a screened interval or a single monitoring point, operators can map water-quality conditions through the full depth of a bore. Profiles collected before injection, during storage and after recovery help distinguish a stable stored-water zone from a migrating plume, a clogged interval or unwanted mixing with native groundwater.

For Australian water utilities, mining operators and environmental researchers, this information supports better decisions about recharge volumes, recovery timing and monitoring frequency. It can also reveal problems early, before declining recovery efficiency or deteriorating water quality affects a production bore.

What a groundwater profiler reveals in an ASR bore

An ASR monitoring program begins with a baseline profile. A sonde or profiling package is lowered through a monitoring bore to record parameters such as electrical conductivity, temperature, pressure, depth and, where appropriate, turbidity, dissolved oxygen or optical indicators of suspended material. The resulting vertical record shows the natural structure of the aquifer and identifies boundaries between fresher and more saline water.

After injection starts, the same intervals can be surveyed repeatedly. Injected water may be cooler or warmer than native groundwater and may have a different conductivity signature. These contrasts make it possible to track the position and thickness of the stored-water body. A profile can show whether recharge remains near the target screen, moves above or below it, or spreads into adjacent formations.

The measurements are most valuable when interpreted alongside pumping rates, injection pressure, recovered volumes and laboratory chemistry. A conductivity front may indicate the movement of injected water, while temperature can reveal mixing or preferential flow. Turbidity changes can point to mobilisation of fine sediment, well development problems or biofouling. A profiler does not replace laboratory testing, but it provides a much denser picture of aquifer behaviour between sampling events.

Establishing a defensible baseline

Baseline work should cover more than a single pre-injection visit. Natural groundwater can change with rainfall, seasonal recharge, nearby pumping and tidal influence in coastal aquifers. Repeated profiles establish the normal range for each depth and help operators separate ASR effects from ordinary aquifer variability.

The survey should include the injection well, recovery well and selected observation bores. In a confined aquifer, pressure responses may travel beyond the visible storage plume, so water-level and pressure measurements are essential. In an unconfined system, the profiler can help identify the water table and the vertical movement of density-driven water. Accurate depth control matters because a small positioning error can make a sharp interface appear to move when it has not.

Australian sites often require a baseline that accounts for salinity. Around Perth’s Gnangara system, for example, groundwater management must consider interactions between urban demand, declining water levels and vulnerable wetlands. In coastal South Australia, saline interfaces and variable recharge can influence whether a conductivity change represents stored source water or intrusion from a more saline zone.

Baseline profiles should be collected using consistent lowering and raising speeds, sensor orientation, equilibration times and logging intervals. Recording the bore condition, purge history and recent pumping activity adds useful context. These details make later comparisons credible and allow a project team to identify genuine changes rather than artefacts caused by inconsistent field practice.

Tracking storage, mixing and recovery

The vertical position of the injected-water plume is a central performance indicator. If it remains within the intended formation, the system is behaving as designed. If it rises toward a shallow aquifer, descends into a lower unit or moves laterally toward a boundary, the operating strategy may need review. Density differences can be especially important: fresher recharge water may move differently from more saline native groundwater, while temperature contrasts can temporarily alter buoyancy.

Profiling results can be converted into practical ASR metrics. The thickness of the recharge zone, the persistence of its conductivity or temperature signature, and the rate at which that signature weakens during recovery all help estimate mixing. Comparing the volume injected with the volume recovered at an acceptable water quality gives a recovery efficiency measure. A falling efficiency may indicate excessive dispersion, an unsuitable storage interval, short residence time or recovery from the wrong depth.

The timing of surveys should follow the operating cycle. A profile immediately after injection documents the initial distribution. Further surveys during storage show whether the plume is stable, while profiles during recovery reveal which layers contribute water first. Repeated measurements over several cycles are more informative than a single detailed campaign because they expose cumulative effects such as clogging, geochemical change or gradual movement into an adjacent unit.

At facilities in the Murray–Darling Basin, where seasonal water availability and salinity management are major considerations, operators may need to compare ASR performance across wet and dry periods. A system that performs well after a high-flow season may respond differently after long periods of low recharge, when native groundwater levels and chemistry have shifted.

Detecting clogging and water-quality risks

Reduced injectivity is often treated as a hydraulic problem, but profiling can help identify its cause. Fine particles in the source water may accumulate around the screen or migrate into the formation. A turbidity response near the injection interval, followed by a change in conductivity or dissolved oxygen, can indicate that physical and biological processes are occurring together.

Optical suspended-solids and turbidity sensors are useful for identifying short-lived events that a laboratory sample may miss. However, fouling, bubbles and changing particle characteristics can affect readings. Sensor stability should therefore be checked throughout the program; practical information on optical drift guidance can help operators recognise when a gradual signal change reflects the instrument rather than the aquifer.

Chemical incompatibility is another risk. Injected water may dissolve minerals, alter redox conditions or mobilise naturally occurring metals. A profiler can identify depth intervals where conductivity, temperature, dissolved oxygen or optical response changes, directing laboratory sampling to the most relevant zones. This targeted approach is useful when a long-screened bore produces a mixed sample that conceals a localised problem.

For projects near Adelaide or other areas where groundwater salinity is closely managed, the distinction between dilution and genuine improvement is important. Lower conductivity does not automatically mean that all water-quality objectives are met. Recovery water still needs to be assessed for nutrients, metals, pathogens and other constituents relevant to the source water and the intended end use.

Integrating profiler data with site operations

A profiler becomes more useful when its measurements are integrated into a common operational model. Water levels show the hydraulic response, flow meters document volumes, pressure data indicate formation resistance, and chemistry identifies changes that sensors alone cannot explain. Combining these records helps determine whether a poor recovery cycle resulted from plume movement, insufficient storage time, screen blockage or a change in pumping conditions.

Monitoring wells should be designed to answer specific questions. Short screened intervals at several depths provide clearer vertical resolution than one long screen, although they increase construction and maintenance costs. In existing bores, a portable profiler may offer an efficient first assessment, especially where access is limited or a project is still in its evaluation phase.

The former D & A Instruments product range, now supported by Campbell Scientific for product and contact information, is relevant to applications involving optical water-quality measurement, suspended solids and environmental monitoring. Equipment selection should consider bore diameter, deployment depth, pressure rating, telemetry, cleaning requirements and compatibility with freshwater or marine conditions. A technical water-quality glossary can also help project teams use terms such as turbidity, suspended solids, conductivity and profiling consistently across field and laboratory reports.

Australian field conditions affect deployment choices. Remote sites in Western Australia may require low-maintenance logging and robust battery systems, while urban projects in Melbourne or Sydney may need compact equipment that can be operated around active infrastructure. In all cases, the monitoring package should be selected around the decision it must support rather than around the maximum number of available sensors.

Turning profiles into management decisions

The final value of profiling lies in how results influence the ASR operating envelope. A stable plume contained within the target interval may support longer storage periods or higher injection volumes. Evidence of rapid mixing may justify shorter cycles, lower injection rates or a different recovery depth. Rising turbidity or increasing pressure at a constant flow rate can trigger maintenance before injectivity declines severely.

Data interpretation should use thresholds agreed before the next operating cycle. Examples include a maximum acceptable conductivity change in recovered water, a pressure increase suggesting clogging, a minimum recovery efficiency or a limit on turbidity. Thresholds should be linked to the intended use of the recovered water and to local regulatory requirements, rather than copied from another aquifer.

For a utility operating a recharge scheme near Perth, profiling may help balance water supply security with groundwater-dependent ecosystem protection. A regional operator in Queensland may use the same approach to evaluate seasonal storage in a different geological setting. The method is transferable, but the baseline, acceptance criteria and sampling frequency must reflect local hydrogeology and the source water.

A strong monitoring record also supports adaptive management and approvals. Each injection and recovery cycle can be compared with the previous one, allowing the operator to refine well maintenance, screen selection, residence time and pumping rates. Over time, groundwater profilers turn an ASR system from a largely hidden subsurface process into a measurable storage asset with observable performance indicators.