Turbidity & suspended solids instrumentation, historically based in Port Townsend, WA Product line now supported through Campbell Scientific, Inc.
A bold yellow angular logo mark set against a deep dark background, sharp and modern
D & A Instruments
Turbidity monitors & water-quality instrumentation

Estimating sediment deposition in navigation harbours with suspended-solids sensors

Navigation harbours need reliable information about where sediment settles, how quickly shoals develop, and when maintenance dredging may be required. Suspended-solids sensors provide a practical way to observe the material moving through the water column, particularly when they are combined with current measurements, water-level data, sediment sampling and periodic surveys of the seabed.

The method is especially useful in Australian ports, where tidal ranges, monsoonal rainfall, river inflows and dredging programs can produce rapidly changing conditions. A sensor cannot measure deposition directly in isolation, but it can reveal the concentration and movement of sediment that may later settle in a berth pocket, approach channel or turning basin.

What suspended-solids sensors actually measure

Optical suspended-solids instruments measure the way particles scatter or absorb light in water. The raw output is generally turbidity, reported in nephelometric units or an equivalent optical scale. With a site-specific calibration, that optical response can be converted into an estimated concentration of total suspended solids, commonly expressed as milligrams per litre.

The measured material may include clay, silt, fine sand, organic particles, plankton and other substances that affect the optical signal. For that reason, turbidity and suspended-solids concentration are related but not interchangeable. A useful reference for terms such as turbidity, suspended solids, backscatter and settling is the water-quality glossary, particularly when several organisations need to use the same monitoring language.

Particle size and colour have a major effect on the result. Two water samples with the same mass concentration can produce different optical readings if one contains dark mineral grains and the other contains pale clay. Flocculated particles also scatter light differently from individual grains. The sensor therefore estimates sediment concentration through calibration rather than measuring mass directly.

Turning concentration into a deposition estimate

The simplest calculation begins with the estimated suspended-solids concentration and the water volume passing through a defined area. If concentration is given in kilograms per cubic metre and discharge is measured in cubic metres per second, the suspended sediment load is:

sediment load = concentration × water discharge

This produces the mass of suspended material moving through the monitored section each second. It does not indicate how much will settle in the harbour. To estimate deposition, the calculation must account for the fraction of particles that settles and the time they remain within the basin.

A more useful conceptual relationship is:

deposition flux = suspended-solids concentration × effective settling velocity

The settling velocity depends on grain size, density, shape, turbulence and flocculation. Near a dredging plume, high turbulence may keep fine particles in suspension. In a quiet berth pocket, the same material may form flocs and settle rapidly. The effective settling velocity should therefore come from local sediment analysis, settling-column tests, validated numerical modelling or a combination of these sources.

Sensor data can also be paired with bed-level change. If the instrument records a pulse of high suspended solids during a spring tide or dredging event, and a multibeam survey later shows shoaling in the same area, the two datasets can be compared. This helps distinguish material that passed through the harbour from material that was retained and deposited.

Designing a monitoring layout

A single sensor at one fixed depth rarely represents the entire water column. Suspended material may be concentrated near the bed during a strong tidal run, while fine particles can remain distributed through the upper water column after a storm or flood. A monitoring program should consider vertical gradients as well as horizontal movement.

A practical layout may include an upstream or background station, one or more sensors near the navigation channel, and additional stations around a berth, turning basin or dredge boundary. Current meters, pressure sensors and water-level records allow the optical data to be related to tidal phase and flow direction. In a large port, a mobile profiler can supplement fixed instruments during different stages of the tide.

Australian conditions make this spatial design particularly important. Port of Brisbane and other estuarine facilities may experience river-driven sediment pulses after heavy rainfall, while Darwin Harbour can see strong seasonal changes during the wet season. In the Pilbara, local dredging and cyclone-related resuspension can create short, intense events that a low-frequency sampling program may miss.

A sensor positioned too close to a pile, quay wall or seabed can record local turbulence rather than representative harbour conditions. Mounting height, orientation, protection from collision and access for servicing should be documented. The deployment plan should also identify whether the objective is compliance monitoring, dredging control, asset planning or a long-term understanding of sediment behaviour.

Field locations worth comparing

Calibration and field validation

Calibration is the foundation of a defensible deposition estimate. Before deployment, operators should collect water samples across the expected range of conditions, including clear water, moderate turbidity and high-concentration events. Samples should be taken beside the sensor and analysed in a laboratory using a recognised suspended-solids method.

The resulting relationship between optical output and laboratory concentration may be linear over a limited range, but it can become non-linear at high concentrations. A single calibration curve may also be unsuitable for all seasons if the sediment source changes. For example, river-borne clay, resuspended channel mud and material released during dredging can have different optical properties.

Calibration checks should be repeated when the sensor is relocated, when the sediment source changes, or when field observations show a shift in performance. Grab samples collected during ebb and flood tides can reveal whether the instrument responds differently to incoming marine water and outgoing estuarine water. Where the data will support a permit, audit or engineering decision, laboratory results and calibration records should be retained with the time series.

Deposition estimates benefit from an independent check. Sediment traps can indicate the mass arriving at a point over a known period, while repeat bathymetric surveys show the net change in bed elevation. These methods measure different parts of the process: traps capture settling material, sensors record suspended transport, and surveys reveal the resulting bed response. Agreement between them is stronger evidence than any one measurement alone.

Managing fouling and long deployments

Biofouling, sediment coating and debris are persistent problems in marine monitoring. A thin film over an optical window can produce a false increase in turbidity, while a buried or partly obstructed sensor may record conditions that do not represent the surrounding water. Fouling can develop quickly in warm, nutrient-rich water, including parts of Moreton Bay, tropical Queensland and northern Australian ports.

Wipers, brushes, copper components, compressed-air systems and scheduled cleaning can extend deployment intervals. The appropriate system depends on water quality, power availability, biofouling pressure and the required measurement duration. An automated cleaning system may be particularly valuable when a station must operate through a dredging campaign or a wet-season period without frequent boat visits; automated cleaning guidance provides relevant background for this type of application.

Cleaning hardware does not remove the need for quality control. Each time the instrument is recovered, operators should inspect the optical face, compare pre-cleaning and post-cleaning readings, and record any evidence of burial or impact. A short clean-water check can identify a drift problem, while comparison with a nearby instrument can help distinguish a local event from an instrument fault.

Quality checks for the time series

Interpreting events in a working harbour

Deposition is usually episodic rather than constant. A channel may receive little material during neap tides, then experience substantial resuspension during spring tides, vessel movements or a strong weather event. Looking only at daily or monthly averages can hide the short periods that control annual shoaling.

Time-series analysis should separate background concentration from event-driven peaks. Tidal stage, current direction, wind, wave activity, rainfall, river discharge and dredging logs should be stored alongside the sensor readings. A rise in suspended solids that coincides with a flood peak may have a different management response from a similar rise caused by propeller wash or a dredge overflow.

For Australian ports, operational context matters. Harbour masters, dredging contractors, environmental consultants and port authorities may each hold part of the information needed to interpret a plume. Terms such as “the works”, “the berth pocket” and “the tide has turned” can refer to precise operational circumstances in local discussions, but they need to be translated into timestamps, locations and measurable variables in the monitoring database.

A strong analysis may calculate the mass passing a cross-section, estimate the proportion likely to settle, and compare the result with observed bed-level change. It can then identify whether deposition is concentrated near a dredge, transported along a channel, or redistributed during vessel movements. This supports decisions about dredge timing, disposal planning, trigger levels and the placement of future monitoring stations.

Building a program that supports decisions

A monitoring program should begin with a clearly stated decision. If the purpose is to assess dredging impacts, the design may need high-frequency data before, during and after the works. If the purpose is to forecast maintenance dredging, longer records of tidal transport, rainfall and bed change may be more valuable than intensive short-term sampling.

Data management is as important as sensor selection. Each record should carry the instrument position, depth, calibration version, maintenance history and quality flags. Automated systems can calculate rolling averages, identify abnormal readings and combine sensor data with tide-gauge or meteorological records. Raw optical output should be preserved so that future recalibration remains possible.

Where equipment is integrated into a broader hydrology or environmental network, open data formats and clear metadata help different contractors and agencies work together. Campbell Scientific now provides product-management and contact information for the D & A Instruments product line, which can be relevant when an existing installation needs technical continuity or replacement planning.

The final result should be expressed in terms that support harbour management: estimated suspended mass, likely deposition zones, confidence ranges, event duration and the evidence behind each estimate. It is better to report a defensible range based on measured calibration and settling assumptions than to present a highly precise deposition figure that the field data cannot support. Used this way, suspended-solids sensing becomes a practical link between water-column measurements and the changing shape of a navigation harbour.